MinkaAire Bolo Manuale delle Istruzioni

INSTRUCTION MANUAL WARRANTY CERTIFICATEBoloBYTM

4 WARNING: All of the parts, hardware and components such as the hanger bracket and hanger ball have been provided for your safety and the prope

OUTLET BOXHANGER BRACKETDOWNRODSUPPLYWIRESFig. 5Fig. 7 Fig. 8Fig. 6 Fig. 10REGISTRATIONSLOTCROSS PINHANGERBALLDOWNRODHITCHPINLOCKPINSET SCREWSSET SCR

55 WARNING:: To avoid possible electrical shock be sure electricity is turned off at the main fuse or breaker box before wiring. NOTE: The

Step 3. Receiver to House Supply Wires Electrical Connections: Connect the WHITE wire (Neutral) from the outlet box to the WHITE wire marked "AC

Fig. 13WHITE (NEUTRAL)WHITE (NEUTRAL)GREEN OR BARECOPPER (GROUND)WHITE ("AC IN N")WHITE ("TO MOTOR N")GROUND-(GREEN)(CONNECT TOGR

6FINISHING THE INSTALLATION Step 1. Slide the canopy up to ceiling and over the two screws on hanger bracket. Rotate canopy clockwise, next, while hol

7Fig 15Fig 16THE FOLLOWING OPERATION MUST BE ACCOMPLISHED BEFORE INSTALLING THE LIGHT KIT.Step 1. Attach the fan blades to the blade holders using the

8Fig 17Step 1. Remove 1 of 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove)Step 2. Place the key holes from the mounting

9Fig. 18 NOTE: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at fuse box.Step 1.

10ATTENTION: The Energy Policy Act of 2005 requires this fan to be equipped with a 190 watt limiting device. If lamping exceeds 190 watts, the ceilin

Manual design and all elements of manual design are protected by U.S. Federal and/or State Law, including Patent, Trademark and/or Copyright laws.

11Fig. 21Fig. 201. Disassemble the switch housing from the light kit, you can keep the light kit for future use. (Fig. 20)2. Attach the plug to the

12OPERATING THE REMOTE CONTROL/WALL CONTROLRestore Power to Ceiling Fan.A. Buttons: These buttons are used to set the fan speeds as fo

Fig 22Fig 23Speed settings for warm or cold weather depend on factors such as room size, ceiling height and number of fans.NOTE: Wait for fan to

13Here are some suggestions to help maintain your fan.1. Because of the fan's natural movement some connections may become loose. Check the suppo

14TROUBLESHOOTINGSYMPTOM Fan will not start Check to make sure the wall switch is turned on.Check circuit fuses or breakers.Caution! Make sure the

SYMPTOM Fan WobbleNOTE: All blade sets are grouped by weight. Because wood and plastic blades vary in density, the fan may wobble even though blades

SYMPTOM Frequency InterferenceTurn the power off to your ceiling fan.Please use a small size tool to change the frequency settings on the control sys

15RPMCFMN.W. G.W. C.F.120120120Fan Size Speed Volts Amps WattsLow MediumHighSPECIFICATIONSThese are typical readings. Your actual fan may vary. They d

Minka-Aire warrants to the original owner that this fan will be free from defects in material an

Date Purchased Store Purchased Model Number S

CONTENTSINSTALLING THE MOUNTING PLATE...INSTALLING THE LIGHT KIT...

SAFETY RULES1 1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box. 2. Be cautious! Read all inst

WARNINGTO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY, MOUNT FAN ONLY TO A U.L. LISTED OUTLET BOX OR SUPPORTING SYSTEM MARKED ACC

214. 60W candelabra bulbs (3) 15. Extra plug16. Balancing kitA. Mounting hardware: #10 x 1.5 Wood screws (2 PCs.) #8 x 3/4" Mac

3Tools Required: Phillips screw driver; slotted screw driver; step-ladder; wire cutters; electrical tape. INSTALLING THE FANMOUNTING OPTIONSIf there